What are the precautions for granulator? – Suzhou Polytime Machinery Co., Ltd.

path_bar_iconYou are here:

What are the precautions for granulator? – Suzhou Polytime Machinery Co., Ltd.

    As a new industry, the plastic industry has a short history, but it has an amazing development speed. With its superior performance, convenient processing, corrosion resistance, and other characteristics, it is widely used in the home appliance industry, chemical machinery, daily necessities industry, and other fields, with unique advantages. However, plastics also have the disadvantage of not easy degradation, so the recycling of waste plastics is particularly important.

    Here is the content list:

    What are the parameters of the granulator?

    What are the precautions for granulator?

    What are the parameters of the granulator?
    The parameters of the granulator machine are divided into specification parameters and technical parameters. Specification parameters include screw diameter, length-diameter ratio, maximum extrusion capacity, main motor power, and center height, etc. The basic parameters include project model, host model, pelletizing specification, pelletizing speed, maximum output, feeding and cooling mode, total power, unit weight, etc.

    What are the precautions for granulator?
    Precautions for placing and using the granulator machine are as follows.

    1. The granulator shall operate in the forward direction to avoid reverse rotation.

    2. No-load operation of the granulator machine is prohibited, and the feeding operation of the hot engine must be carried out, to avoid stick bar (also known as shaft holding).

    3. It is forbidden to enter ironware and other sundries in the feed inlet and vent hole of the plastic granulator machine. So as not to cause unnecessary accidents and affect safe and normal production.

    4. Pay attention to the temperature change of the machine body at any time. When touching the strip with clean hands, it shall be heated immediately. Until the strip is normal.

    5. When the reduced bearing burns or is accompanied by noise, it shall be shut down for timely maintenance and supplemented with oil.

    6. When the bearings at both ends of the main engine bearing room are hot or noisy, stop the machine for maintenance and add oil. During normal operation, the bearing chamber shall be filled with oil every 5-6 days.

    7. Pay attention to the operation law of the machine; For example, if the machine temperature is high or low and the speed is fast or slow, it can be handled in time according to the situation.

    8. In case of unstable operation of the fuselage, pay attention to check whether the fitting clearance of the coupling is too tight and loosens it in time.

    9. It is strictly prohibited for irrelevant personnel to talk with the equipment operator, and only one person is allowed to operate the button command on the electric control panel.

    10. Regularly check the insulation effect of wires and circuits, and always pay attention to the warning contents on the warning board of the machine.

    11. before the power distribution cabinet has been cut off, it is strictly forbidden for non-professional personnel to open the cabinet door, and it is strictly forbidden to adjust the cutter before the cutter is completely stationary.

    12. When the moving parts and hopper are blocked, do not use hands or iron rods, but only plastic rods to handle them carefully.

    13. Cut off the materials in the motor after the power failure, and clean them in time after the next carbonization.

    14. In case of machine failure, stop the operation of the machine the first time, and do not claim it on your own. And inform and wait for the machine maintenance personnel to check and repair or call to guide the maintenance.

    15. Prevent machine damage and industrial accidents caused by all factors; Operate in strict accordance with the standard operation methods to reduce the occurrence of faults or accidents.

    All countries have attached great importance to the research and improvement of waste plastics recycling technology in the world. The recycling of waste plastics has great investment potential and market. To coordinate the development of resources and the environment and achieve sustainable economic development, it is urgent to improve the recovery rate of waste plastics through a waste plastic granulator. Since its establishment in 2018, Suzhou Polytime Machinery Co., Ltd. has developed into one of China's large extrusion equipment production bases, with a professional and efficient team in technology, management, sales, and service. If you have the intention to buy a plastic granulator, you can consider our high-quality products.

Contact Us